Domotica wall plug

DI Plus Read user experiences here. "The ULTRASOUND DI Plus is a very powerful tool for any musician. This is not only a DI but a full featured preamp designed after our famous AG-series amps. Whether at a local open mic night or at a major concert venue, you will be able to dial in the clear natural acoustic sound that our amplifiers are known for, and route it to the stage PA through a balanced XLR output. Sound engineers will appreciate the versatile controls and the optional 48-volt phantom power operation. Therefore, no more wall warts or batteries if your mixer has phantom power. (Originally called ULTRA PDI.) INSTRUMENT INPUT: This input is designed for all passive and active type pickup signals. When a plug is inserted, the 9V battery is switched on. INSTRUMENT OUTPUT: This is a "parallel" jack which can be used to send the "guitar/instrument signal" to an external tuner, guitar amp or other device which can use an instrument level signal. EFX LOOP: This is a real world "EFX LOOP". In an effort to save room, most of our competition uses a TRS jack (tip, ring, sleeve) and Y cable type system. The DI+ is provided with two 1/4" jacks, one for "SEND" and one for "RETURN". Since the EFX LOOP interrupts the signal path it can be used as an insert point for a volume pedal, compressor, or tuner, if the tuner is equipped with a bypass switch. (Try that with one of our competitors units) SEND: The signal on the SEND jack is post-input gain and pre EQ. This means that you can use the SEND signal as an auxiliary unbalanced direct output. This signal is not affected by any of the panel controls with exception of the "INPUT GAIN" control. RETURN: A plug inserted into the RETURN jack will interrupt the signal path. The signal on the tip of the plug inserted into the RETURN jack will be the signal that the DI Plus will process. INPUT GAIN: The "INPUT GAIN" is not a volume control, rather this control sets the level of amplification applied to the input signal to boost it to a useable level. The reason this is adjustable is to accommodate a wide range of pickup devices. BASS: This is an "Active" control. The BASS control adjusts the amount of cut or boost in the low frequency (150HZ) range. TREBLE: This is an "Active" control. The TREBLE control adjusts the amount of cut or boost in the high frequency (5kHZ) range. NOTCH FILTER: ON/OFF - Enables or disables the NOTCH FILTER control. FREQ. HZ - Sets the frequency (100-350HZ) of the 18db cut NOTCH FILTER that is used to control resonant feedback. SHAPE: ON/OFF - This toggle switch enables or disables the SHAPE control. This control is a mid dip control. In the ON position, the mid frequencies will be cut and the high and low frequencies will be boosted. PHASE: IN/OUT - Changes the polarity of the signal. Phase affects the way the guitar top is pressurized by the loudspeakers. When the signals are out of phase with each other, low-end feedback is minimized. If you experience ⤽positive acoustic⤝ feedback on stage, flip the phase switch from its current setting to see if this will kill the feedback. If inverting phase alone does not eliminate feedback, the notch filter can be used. Phase will also affect the way the guitar signal mixes live and when recording. XLR LEVEL: This control adjusts the amount of signal sent to the XLR OUT jack. LINE LEVEL: This control adjusts the amount of signal sent to the LINE OUT jack. 48V: (Phantom Power) This LED lights when there is 48V Phantom Power present on the XLR OUT jack. No battery drain will occur when Phantom Power is present. POWER: This LED indicates the DI PLUS is ready to operate. The POWER LED will illuminate when: A. A plug is inserted into the INPUT jack and there is a fresh battery installed in the DI PLUS. B. A 9VDC adapter (Wall Wart) is plugged into the power jack. (9VDC Regulated Power Supply - 500mA) (2.1MM DC Power Plug, Center +) C. There is 48V phantom power on the XLR cable plugged into the XLR OUT jack. (The 48V LED and the POWER LED will both be illuminated.) XLR OUT: Plug a standard XLR cable from your PA or recording console into this low impedance balanced output. Use the "XLR LEVEL" control to set the output level which matches up best with your PA or recording gear and gives you the least amount of noise. If your board provides 48V phantom power on the XLR cables, the DI Plus will run from this and save the battery. It is suggested that you keep a battery in the unit as a backup when using the phantom power. If the phantom power drops, the DI Plus will automatically switch to battery power. LINE OUT: This is a standard unbalanced line level output signal. Use the "LINE LEVEL" control to adjust the signal level on this jack. This output can be used simultaneously with the XLR OUT jack for some creative signal routing. Plug a standard instrument cable from this output to a stage monitor amp or unbalanced Mic input on a mixer.

DI Plus Read user experiences here. "The ULTRASOUND DI Plus is a very powerful tool for any musician. This is not only a DI but a full featured preamp designed after our famous AG-series amps. Whether at a local open mic night or at a major concert venue, you will be able to dial in the clear natural acoustic sound that our amplifiers are known for, and route it to the stage PA through a balanced XLR output. Sound engineers will appreciate the versatile controls and the optional 48-volt phantom power operation. Therefore, no more wall warts or batteries if your mixer has phantom power. (Originally called ULTRA PDI.) INSTRUMENT INPUT: This input is designed for all passive and active type pickup signals. When a plug is inserted, the 9V battery is switched on. INSTRUMENT OUTPUT: This is a "parallel" jack which can be used to send the "guitar/instrument signal" to an external tuner, guitar amp or other device which can use an instrument level signal. EFX LOOP: This is a real world "EFX LOOP". In an effort to save room, most of our competition uses a TRS jack (tip, ring, sleeve) and Y cable type system. The DI+ is provided with two 1/4" jacks, one for "SEND" and one for "RETURN". Since the EFX LOOP interrupts the signal path it can be used as an insert point for a volume pedal, compressor, or tuner, if the tuner is equipped with a bypass switch. (Try that with one of our competitors units) SEND: The signal on the SEND jack is post-input gain and pre EQ. This means that you can use the SEND signal as an auxiliary unbalanced direct output. This signal is not affected by any of the panel controls with exception of the "INPUT GAIN" control. RETURN: A plug inserted into the RETURN jack will interrupt the signal path. The signal on the tip of the plug inserted into the RETURN jack will be the signal that the DI Plus will process. INPUT GAIN: The "INPUT GAIN" is not a volume control, rather this control sets the level of amplification applied to the input signal to boost it to a useable level. The reason this is adjustable is to accommodate a wide range of pickup devices. BASS: This is an "Active" control. The BASS control adjusts the amount of cut or boost in the low frequency (150HZ) range. TREBLE: This is an "Active" control. The TREBLE control adjusts the amount of cut or boost in the high frequency (5kHZ) range. NOTCH FILTER: ON/OFF - Enables or disables the NOTCH FILTER control. FREQ. HZ - Sets the frequency (100-350HZ) of the 18db cut NOTCH FILTER that is used to control resonant feedback. SHAPE: ON/OFF - This toggle switch enables or disables the SHAPE control. This control is a mid dip control. In the ON position, the mid frequencies will be cut and the high and low frequencies will be boosted. PHASE: IN/OUT - Changes the polarity of the signal. Phase affects the way the guitar top is pressurized by the loudspeakers. When the signals are out of phase with each other, low-end feedback is minimized. If you experience “positive acoustic” feedback on stage, flip the phase switch from its current setting to see if this will kill the feedback. If inverting phase alone does not eliminate feedback, the notch filter can be used. Phase will also affect the way the guitar signal mixes live and when recording. XLR LEVEL: This control adjusts the amount of signal sent to the XLR OUT jack. LINE LEVEL: This control adjusts the amount of signal sent to the LINE OUT jack. 48V: (Phantom Power) This LED lights when there is 48V Phantom Power present on the XLR OUT jack. No battery drain will occur when Phantom Power is present. POWER: This LED indicates the DI PLUS is ready to operate. The POWER LED will illuminate when: A. A plug is inserted into the INPUT jack and there is a fresh battery installed in the DI PLUS. B. A 9VDC adapter (Wall Wart) is plugged into the power jack. (9VDC Regulated Power Supply - 500mA) (2.1MM DC Power Plug, Center +) C. There is 48V phantom power on the XLR cable plugged into the XLR OUT jack. (The 48V LED and the POWER LED will both be illuminated.) XLR OUT: Plug a standard XLR cable from your PA or recording console into this low impedance balanced output. Use the "XLR LEVEL" control to set the output level which matches up best with your PA or recording gear and gives you the least amount of noise. If your board provides 48V phantom power on the XLR cables, the DI Plus will run from this and save the battery. It is suggested that you keep a battery in the unit as a backup when using the phantom power. If the phantom power drops, the DI Plus will automatically switch to battery power. LINE OUT: This is a standard unbalanced line level output signal. Use the "LINE LEVEL" control to adjust the signal level on this jack. This output can be used simultaneously with the XLR OUT jack for some creative signal routing. Plug a standard instrument cable from this output to a stage monitor amp or unbalanced Mic input on a mixer.

La telecamera Wi-Fi da interno Full HD Ezviz C1C Plus è una telecamera ad alta risoluzione che rappresenta la scelta ideale per la protezione dei tuoi ambienti. Una telecamera da interno studiata apposta  per garantirti una visione sempre nitida di giorno e di notte. Ezviz C1C Plus - Telecamera Wi-Fi da interno Fra le soluzioni di videosorveglianza Ezviz per la domotica wireless, questa telecamera da interno senza fili rappresenta la scelta ideale per la protezione dei tuoi ambienti interni. Funzioni di domotica wireless La telecamera da interno Wi-Fi 2.4G Ezviz è controllabile da remoto tramite la app Ezviz dal tuo Smartphone. È una telecamera Wi-Fi compatibile con Google Home e Amazon Alexa. Potrai quindi integrarla senza problemi con il tuo assistente vocale preferito. La tecnologia delle telecamere Ezviz Le telecamere Ezviz offrono il miglior rapporto qualità/prezzo sul mercato della domotica wireless, garantendoti funzionalità all'avanguardia ad un prezzo contenuto. Telecamera WiFi da interno FullHD; Risoluzione 1080p 2MP; Visione notturna; Audio bidirezionale; POV 106° orizzontale, 130° diagonale; Telecamera con supporto microSD classe 10 U1 fino a 256GB (microSD non inclusa nella confezione); App Ezviz per videosorveglianza: controlla le tue telecamere Ezviz dovunque tu sia e in qualsiasi momento. Telecamera Wi-Fi per casa con visione notturna chiara e nitida Telecamera da interno con visione notturna migliorata, per una protezione 24 ore su 24. Grazie ad una avanzata tecnologia ad infrarossi con configurazione ottica migliorata si ottiene un'ottima visibilità fino a 12 metri anche in condizioni di scarsa luminosità. Telecamera da interno Plug&Play La base magnetica e lo snodo della telecamera Ezviz C1C Plus rendono l'installazione facile e veloce. È sufficiente posizionarla su una mensola o fissarla su una parete o sul soffitto. Una volta configurata, puoi regolare manualmente l'inquadratura in base alle tue esigenze. App Ezviz per videosorveglianza La telecamera Ezviz C1C Plus possiede un'efficiente app per videosorveglianza per la tua casa e, in caso di movimento, invia notifiche in tempo reale sul tuo smartphone con le immagini acquisite (notifiche istantanee attivabili manualmente). La telecamera WiFi da interno FullHD Ezviz C1C Plus è dotata di microfono e altoparlante integrati per comunicare con i tuoi cari o con i tuoi amici a 4 zampe. Utilizzando l'app Ezviz sul tuo smartphone, puoi vedere, parlare e ascoltare facilmente ovunque tu sia.

PRODOTTO RIGENERATO Specifiche Display Dimensione Diagonale 55" Tipo pannello 60Hz E-LED BLU Risoluzione 1920 x 1080 (16:9) Passo pixel (orizz. x vert.) 0,630(orizzontale) x 0,630(verticale) Contrasto4000:1 Angolo di visione (orizz./vert.)178/178 Tempo di risposta 8 ms Numero di colori 10 bit Dithering - 1,07 Miliardi Gamma colori 72 % Frequenza H-Scanning 30 ~ 81kHZ Frequenza Pixel Massima 148.5MHz Frequenza V-Scanning 48 ~ 75HZ Luminosità 500 nit Rapporto di contrasto dinamico Mega Connettività Ingresso HDMI 2 Ingresso DP 1 Ingresso DVI 1 Ingresso Tuner N/D USB2 Ingresso Component N/D Ingresso Composite N/D Ingresso RGB D-Sub (DVI-I comune) Ingresso audio Stereo Mini Jack, RGB/DVI/DP/HDMI Uscita audio Stereo Mini Jack Uscita video DP1.2(Loop-out) Ingresso RS232 Sì Uscita RS232 Sì Ingresso RJ45 Sì SD Card Slot N/D Design Tipo di base Supporto (optional) Alimentazione Consumo energetico (spento) meno di 0,5 W Consumo energetico (acceso) Max:187W / Tipico:(EU)115, (US)55, (WW)115W / BTU(Max): 637.67W Consumo energetico (Sleep Mode) meno di 0,5 W Dimensioni: Dimensioni (LxAxP) 1228,4 x 701,2 x 29,9 mm Dimensioni Totali con imballaggio (LxAxP) 1335 x 812 x 182 mm Peso: Peso unità 16,3 kg Peso Totale con imballaggio 21,8 kg Specifiche Meccaniche VESA Mount 400 x 400 mm Larghezza Cornice 6,9 (superiore)/ 6,9 (laterale)/ 8,9 (inferiore) mm Media Player Option Type SBB, PIM Ready Condizioni di funzionamento: Temperatura 0~40 â,,f Umidità 10~80 (non condensante) Caratteristiche generali: Speciale Pannello antiriflesso, Sensore della temperatura, Video Wall (15x15(OSD)), Video Wall Daisy Chain (16),Schermo orientabile, Batteria orologio (fino a 80 ore), Altoparlante integrato (10 W x 2), Modulo Wi-Fi integrato, IP5x, Sensore IR centrale Altoparlante10 W x 2 Caratteristiche Opzionali: Attacco WMN4270SD SpecialtyCML450H BaseSTN-L4655E Funzioni speciali: SpecialeMagic Clone (su USB), Recupero e commutazione automatica sorgente, RS232C / RJ45 MDC, Plug and Play, PIP/PBP, Rotazione immagine, Blocco tasti, DP 1.2 Digital Daisy Chain (supporto HDCP), Aggiornamento firmware da rete, Nuova schermata Home, VideoWall senza PC, Multicanale, Controllo da dispositivo mobile, Programmazione eventi, Lettore multimediale di riserva Supporto MagicInfoSìEco Classe di efficienza energetica:A

DESCRIZIONE • Dual Input • TV TUNER INTEGRATO • Tempo di Risposta: 8ms • HD-TV Ready • Televideo • Telecomando • Wide 16:10 Telecomando Incluso, televideo, HDTV Ready, W/W TV System, Virtual Dolby, BBE, PIP & PBP SPECIFICHE TECNICHE Pannello Area visibile: 19" WIDE 16:10 Pixel Pitch (mm): 0,294 Luminosità: 300 cd/m2 Rapporto di contrasto: 700:1 Angolo di visuale (orizz/vert): 160° / 160° Tempo di risposta (ms): 8ms Frequenze Orizzontale (kHz): 33~81 kHz Verticale (Hz): 56~75 Hz Risoluzione massima 1440 x 900 Colori - Massimo supportato 16.7 Milioni Segnale d'ingresso Segnale video: Analog RGB, DVI Digital Link:TMDS, Composite S-video, Component, TV(antenna/cable), SCART Sync. Type: Separate H/V, Composite Connettori: 15pin D-sub, DVI-D CVBS, S-Video, SCART Component, RF Plug & Play DDC: DDC 1/2B Compatibilita’ MAC Si’ Consumi Acceso: 55 Watts (Max.) Sleep Mode: Alimentatore: integrato Wall Mount Opzionale (VESA 100) Certificazioni CE / TCO'99 Colore Cabinet Silver Dimensioni (LxAxP) Con base (mm): 466x406x216

Marchio: Two notes Categoria: Accessori per amplificatori Load Box reattiva compatta (8 Ohm, 100 Watt RMS) Attenuatore a tre modalità: Home (38dB), Club (20dB), Stadio (0dB) Simulazione di cabinet e microfoni Torpedo con tecnologia IR Doppio IR loader: 512 slot per caricare file IR 32 Cabinet virtuali, 128 Preset 6 Preset assegnabili e richiamabili attraverso il selettore Preset Scegli tra 8 microfoni per ogni cabinet e 8 simulazioni di ambienti Uscite DI XLR DI (Stereo, Dual Mono, Dry/Wet) Uscita cuffie e connessione MIDI Riverbero stereo con controllo hardware Space EQ Semi parametrico, controllo hardware Voicing Funzione Twin Tracker per "radoppiare" il segnale come un secondo chitarrista Enhancer con controlli di Body, Brilliance e Thickness Noise Gate Plug In Wall of Sound incluso Licenze ufficiali di MESA/Boogie, Celestion, Orange, Suhr, REVV e molti altrii Editor Torpedo Remote tramite USB o Bluetooth Accessori: Alimentatore 12V incluso Dimensioni: 128 x 175 x 64 mm Peso: 1.3 Kg

Marchio: Two notes Categoria: Altri Processori di Segnale Reactive Load Box (16 Ohm, 100 watt RMS) Attenuatore a tre modalità: Home (-38dB), Club (-20dB), Stadium (0db) Simulazione di cassa e microfoni Torpedo IR-based technology Dual IR Loader: 512 slots per caricare file IR personali 32 Virtual Cabinets, 128 preset 6 preset assegnabili e richiamabili attraverso il selettore PRESET Scegli tra 8 microfoni per ogni cabinet e 8 simulazioni di stanze XLR DI Outputs (Stereo, Dual Mono, Dry / Wet) Uscita cuffie e connessione MIDI Riverbero stereo con controllo SPACE hardware EQ Semi-parametrico, controllo hardware di VOICING Funzione Twin Tracker per «doppiare» il segnale come un secondo chitarrista Enhancer con controlli di Body, Brilliance e Thickness Noise gate Plug In Wall of Sound plugin incluso Licenze ufficiali di MESA/Boogie, Celestion, Orange, Suhr, REVV e molti altri Editor Torpedo Remote via USB o bluetooth Dimensioni: 128 (w) x 175 (d) x 64 (h) mm Peso: 1.3 kg Alimentatore 12V incluso