Input connectors

Marchio: Audiophony Categoria: Finali di potenza Class-D amplifier Switched-mode power supply Mode selection: Stereo, Bridge or Parallel Independent limiter for each channel Extremely accurate and independent level settings for each channel LEDs indicators Convection cooled Balanced Jack TRS and XLR inputs Unbalanced RCA outputs Binding post-jacks or speakON outputs Short-circuit, over current and high temperature independent protections for each channel 2x19" rack mount spaces Stereo Max power: 4 Ω RMS stereo power (minimum): 2 x 150 W RMS; 8 Ω RMS stereo power: 2 x 80 W RMS Mono bridged Max power: 8 Ω bridged power (minimum): 1 x 300 W RMS Signal-to-noise ratio Less than 90 dB Input sensitivity: 4 dBu +/-2 dB Distortion: THD at 1 kHz 1/2 rated power Less than 0.1%; Slew rate: - 65 dB at 1 kHz; Frequency response (4 Ω/1 W): +0.5 dB; 20 Hz-20 kHz Input impedance: unbalanced 15 kΩ / Balance 30 kΩ Clip: 0 dBr Cooling: Convection cooled Input connectors: XLR3-F, Balanced 6.35 mm TRS-F jack + Unbalanced RCA Output connectors: Binding post-jacks + 4-pole speakON® Front control panel: AC power switch, Channel 1 and 2Volume Rear control panel: Mode selection button Indicators: Protect (red) / Clip (yellow) / Signal (green) Protections: Short-circuits, over current and high temperature protected Power supply: 100/230 V AC - 50/60 Hz Dimensions: 482 mm x 44 mm x 330 mm NetWeight: 4.3 kg

Marchio: Audiophony Categoria: Finali di Potenza Class-D amplifier Switched-mode power supply Mode selection: Stereo, Bridge or Parallel Independent limiter for each channel Extremely accurate and independent level settings for each channel LEDs indicators Convection cooled Balanced Jack TRS and XLR inputs Unbalanced RCA outputs Binding post-jacks or speakON outputs Short-circuit, over current and high temperature independent protections for each channel 2x19" rack mount spaces Stereo Max power: 4 Ω RMS stereo power (minimum): 2 x 150 W RMS; 8 Ω RMS stereo power: 2 x 80 W RMS Mono bridged Max power: 8 Ω bridged power (minimum): 1 x 300 W RMS Signal-to-noise ratio Less than 90 dB Input sensitivity: 4 dBu +/-2 dB Distortion: THD at 1 kHz 1/2 rated power Less than 0.1%; Slew rate: - 65 dB at 1 kHz; Frequency response (4 Ω/1 W): +0.5 dB; 20 Hz-20 kHz Input impedance: unbalanced 15 kΩ / Balance 30 kΩ Clip: 0 dBr Cooling: Convection cooled Input connectors: XLR3-F, Balanced 6.35 mm TRS-F jack + Unbalanced RCA Output connectors: Binding post-jacks + 4-pole speakON® Front control panel: AC power switch, Channel 1 and 2Volume Rear control panel: Mode selection button Indicators: Protect (red) / Clip (yellow) / Signal (green) Protections: Short-circuits, over current and high temperature protected Power supply: 100/230 V AC - 50/60 Hz Dimensions: 482 mm x 44 mm x 330 mm NetWeight: 4.3 kg

1400W + 700W – 137DB SPL ACTIVE PRECISION COVERAGE VERTICAL ARRAY 2-way powered bi-amplified true line array, bass reflex design, internal Digital Signal Processor 1400Wrms LF and 700Wrms HF Class D (PWM) high efficiency integrated amplifier 8 woofer custom al neodimio da 200mm (8’’)50 mm voice coil (2”) 8 x 25 mm (1”) custom neodymium compression drivers and 44 mm voice coil (1.7”) 8 polypropylene waveguide horns with 90° horizontal dispersion 15° vertical dispersion On-board presets allow different equalization configurations, gain and digital delay through the rear control panel Specifications Configuration way: 2 Built-in amplifiers LF/HF (Wrms): 1400/700 Frequency response (-6dB): 58Hz – 18kHz Low frequency woofer (inch): 8 x 8 – 2 coil – neodymium High frequency driver (inch): 8 x 1 – 1,7 coil – neodymium Sensitivity (1W/1m): 105 dB Maximum SPL: 137 dB Dispersion (H x V): 90° x 15° Input impedance (kohm): 22 Crossover frequency (kHz): 1,2 AC Power requirements (VA): 1400 Input connectors: XLR with loop Power cord: 5 / 16,4” (m/ft) Net dimensions (WxHxD – single unit): 713x980x460 / 28,1×38,6×19,3 (mm / inch) Net weight (kg/Lb): 93 / 205,02 Transport dimensions (WxHxD – 2 units on pallet): 750x1400x1100 / 29,5×55,1×43,3 (mm / inch) Transport weight (2 units on pallet): 210 / 462,97 (kg/Lb) PRODOTTO USATO: CONDIZIONI OTTIME

The Yamaha AX Series 15" bass reflex subwoofer, complements the AX10, AX12, and AX15. Features include robust carpet covering, metal grilles and handles, pole mount socket. Frequency response covers the low bass range from 50Hz up to 200Hz, with 1000W peak power handling to move lots of air, enough to get your trouser legs flapping in the breeze. Caratteristiche Bass reflex enclosure. 15" speaker. 35mm pole mount socket. Frequency Response 50Hz-200Hz. Power Handling: 250W Noise, 500W Program, 1000W Maximum. 8 ohm nominal impedance. 97dB SPL 1W 1 meter. Input Connectors: 2 1/4" phone jack, 2 Neutrik Speakon NL4MP. Dimensions (W x H x D): 485 x 618 x 505. Weight: 26.5kg. Made in USA

Marchio: Boss Categoria: Pedali Riverbero Suono di qualità da studio con conversione AD/DA a 32-bit, elaborazione a 32-bit in virgola mobile e frequenza di campionamento di 96 kHz 12 modalità con 21 tipi di riverbero, tutti modificabili dettagliatamente Include una vasta scelta di tipi di riverbero, dagli effetti standard a quelli più avanzati, oltre a classici Roland come l’SRV-2000 Reverb e RE-201 Space Echo Il modo A/B Simul vi consente di usare due patch di riverbero contemporaneamente La funzione “carryover” selezionabile permette alle code del riverbero di proseguire quando cambiate patch o ponete l’effetto in bypass Il potente DSP fornisce un delay digitale con modulazione indipendente, insieme ad ogni patch di riverbero LCD grafico e potenti opzioni di controllo in tempo reale 297 memorie interne per le patch e pratici controlli a portata di mano Funzionamento con “buffered-bypass” o “true-bypass” selezionabile Ingresso/uscita MIDI per interfacciarsi con dispositivi di controllo MIDI USB-MIDI per la connessione con l’RV-500 Editor/Librarian o una DAW Funziona con quattro batterie AA o un trasformatore in CA della serie PSA Frequenza di Sampling: 96 kHz Conversione AD/DA: 32 bit Nominal Input Level INPUT A/MONO, B: -10 dBu Maximum Input Level INPUT A/MONO, B: +8 dBu Input Impedance INPUT A/MONO, B: 1 M ohm Nominal Output Level OUTPUT A/MONO, B: -10 dBu Maximum Output Level OUTPUT A/MONO, B: +8 dBu Output Impedance OUTPUT A/MONO, B: 2 k ohms Recommended Load Impedance OUTPUT A/MONO, B: 20 k ohms or greater Bypass Buffered bypass or True bypass (with relays) INPUT (A/MONO, B) jacks, OUTPUT (A/MONO, B) jacks: 1/4-inch phone type CTL 1,2/EXP jack: 1/4-inch TSR phone type USB COMPUTER port: USB type B MIDI (IN, OUT) connectors DC IN jack

Marchio: BOSS Categoria: Pedali Riverbero Suono di qualità da studio con conversione AD/DA a 32-bit, elaborazione a 32-bit in virgola mobile e frequenza di campionamento di 96 kHz 12 modalità con 21 tipi di riverbero, tutti modificabili dettagliatamente Include una vasta scelta di tipi di riverbero, dagli effetti standard a quelli più avanzati, oltre a classici Roland come l’SRV-2000 Reverb e RE-201 Space Echo Il modo A/B Simul vi consente di usare due patch di riverbero contemporaneamente La funzione “carryover” selezionabile permette alle code del riverbero di proseguire quando cambiate patch o ponete l’effetto in bypass Il potente DSP fornisce un delay digitale con modulazione indipendente, insieme ad ogni patch di riverbero LCD grafico e potenti opzioni di controllo in tempo reale 297 memorie interne per le patch e pratici controlli a portata di mano Funzionamento con “buffered-bypass” o “true-bypass” selezionabile Ingresso/uscita MIDI per interfacciarsi con dispositivi di controllo MIDI USB-MIDI per la connessione con l’RV-500 Editor/Librarian o una DAW Funziona con quattro batterie AA o un trasformatore in CA della serie PSA Frequenza di Sampling: 96 kHz Conversione AD/DA: 32 bit Nominal Input Level INPUT A/MONO, B: -10 dBu Maximum Input Level INPUT A/MONO, B: +8 dBu Input Impedance INPUT A/MONO, B: 1 M ohm Nominal Output Level OUTPUT A/MONO, B: -10 dBu Maximum Output Level OUTPUT A/MONO, B: +8 dBu Output Impedance OUTPUT A/MONO, B: 2 k ohms Recommended Load Impedance OUTPUT A/MONO, B: 20 k ohms or greater Bypass Buffered bypass or True bypass (with relays) INPUT (A/MONO, B) jacks, OUTPUT (A/MONO, B) jacks: 1/4-inch phone type CTL 1,2/EXP jack: 1/4-inch TSR phone type USB COMPUTER port: USB type B MIDI (IN, OUT) connectors DC IN jack

H.H Scott LK-72 Amplificatore valvolare vintage in perfetto stato, se vende con le valvole originale SCOTT al 90% fabbricante la General Electric, amplificatore costruito nei anni 60 per la dita Scott Company Americana, qualita garantita come amplificatore HI-FI. si caratterizza per la sua armonia e qualita del audio, concorrente ad amplificatore come Mctouch, utilizza la stessa configurazione e valvole. Si ha fatto una assistenza tecnica molto rigorosa, sostituiti i suoi condensatori che per usura dal tempo non rendeva il livello tecnico, compresso il analisi in banco di prova della sua qualita di risposta in frequenza con dei strumenti che ci permettono venderlo con sei (6) messi di garanzia. Qualsie se domanda non essitare a chiedere piacere da rispondere le Vostre domande. Dentro del territorio Italiano il trasporto è a carico nostro. VINTAGE AMPLIFIER HI-FI VALVULAR AMPLIFIER. FULLY RESTORED, FULL RECAPPING EXCELLENT ELECTRONIC CONDITION. warranty the audio quality PUSH-PULL AMPLIFIER WITH ORIGINALS TUBES SCOTT. Vintage, amplifier push-pull with 7591 (four tubes) H.H. SCOTT LK-72 A restoration was carried out verifying all its mechanical and electronic elements, the pass capacitors were replaced guaranteeing an excellent quality audio HI-FI. The power output uses tubes 7591 (four-unit push-pull), Second Audio and Stage phase splitter 6U8 / 6GH8 (two tubes), pre-amplifier to phone, and aux input 12AX7, two tubes for PHONO preamplifier, and two tubes for aux preamplifier input, all tubes are including too. The restored circuit also uses especially resistors on carbon, and the oil-paper capacitor is selected and of high quality, for this reason, is possible to warranty low noise without parasitic noises, including your copy manual and electronics diagram. warranty 1 year for bad work. The amplifier is sold tested for the 7591 - Preamplifier to phone is including with RIIA and NAB filter, RUMBLE FILTER too, tape monitor, is possible the interconnection with your magnetic or ceramic head to phone. - It's including two (2) external signal input hi-level with RCA connectors, in this input, it's possible to connect the CD OR ANOTHER DECK for example. - External speaker is possible to connect with 16 - 8 and 4 ohms. including the control for rev stereo mono or single-channel selector. separate control for treble and Bass, loudness control to all the commands work in good condition. FIRST TO BUY THE AMPLIFIER, PLEASE SEND THE ZIP CODE FOR CALCULATED THE SHIPPING COST. THE SHIPPING COST IS NOT INCLUDING OUT TO ITALY, THE PACKING IS FOR 15 KG AND INSURANCE, THE SIZE BOX REQUEST IS 55 X 50 X 40 CM Weight 22 kg. Any question. It's a possibility to request

INTERFACES CONNECTORS ANALOG INPUT CONNECTOR VGA DIGITAL INPUT CONNECTOR DVI-D, HDMI HDCP yes,altre caratteristiche rilevabili dal sito del produttore.Vendo il monitor come nuovo per passaggio a 32".Ritiro a mano o eventualmente anche spedibile

Behringer Ultragraph Pro FBQ1502 Equalizzatore rack stereo a 15 bande, uscita sub, ricerca feedback, low cut, silenzioso, perfetto. Vendo 65€. 110€ se abbinato al case a 3 unitá. Solo case 50€. Caratteristiche tecniche: -Professional 15-band stereo graphic equalizer for live and studio applications -Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer -Dedicated mono subwoofer output with adjustable crossover frequency -Additional low-cut filter removes unwanted frequencies, e.g. floor rumble -Highly accurate 4-segment LED output metering and input gain controls for easy level setting -Ultra-low noise audio operational amplifiers for highest signal integrity -Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors -Shielded toroidal power transformer for ultra-low noise performance -3-Year Warranty Program* -Designed and engineered in Germany

Marchio: Audiophony Categoria: Sistemi a Colonna e Line Array Power handling: 80W RMS / 160W max. Frequency response: 135 Hz - 17 KHz Axial sensitivity(1W/1m): 92 dB SPL max.: 114 dB Nominal impedance: 8 Ohms Speakers: 4 x 3" Size: 110 x 350 x 148,5 mm Net weight: 4 Kg Horizontal dispersion: 115° Vertical dispersion: 20° Connectors: Input/output Speakon Materials: Die-cast aluminium housing Integral steel grill protection Mounting Systems: Wall mout bracket plate: iLINE43sup Mounting socket for speaker stand

Marchio: Audiophony Categoria: Casse da Installazione Power handling: 80 W RMS / 160 W max. Frequency response: 135 Hz - 17 kHz Sensitivity(1W/1m): 92dB SPL max.: 114dB Nominal impedance: 8 ohm Speakers: 4 x 3" Dimensions: 110 x 350 x 148 mm NetWeight: 4 kg Horizontal dispersion: 115° Vertical dispersion: 20° Connectors: Input/output speakON Materials: Die-cast aluminium housing Integral steel grill protection Mounting Systems: Wall mout bracket plate: iLINE43sup Mounting socket for speaker stand

Marchio: Audiophony Categoria: Sistemi a Colonna e Line Array Power handling 160 W RMS / 320 W max. Frequency response 135 Hz - 17 kHz Sensitivity(1W/1m) 95dB SPL max. 120dB Nominal impedance 16ohm Speakers 8 x 3" Dimensions 110 x 690 x 148 mm NetWeight 7,6 kg Horizontal dispersion 115° Vertical dispersion 20° Connectors Input/output speakON Materials Die-cast aluminium housing Integral steel grill protection Mounting Systems Wall mout bracket plate: iLINE83sup Mounting socket for speaker stand