Mid frequency

DYNAUDIO MW 162 COPPIA MID WOOFER SERIE ESOTEC Thiele Small Parameters Nominal impedance Znom 4 ? DC resistance Re 3.1 ? Voice coil inductance Le 0.22 mH Resonance frequency fs 55 Hz Mechanical Q factor Qms 2.2 Electrical Q factor Qes 0.57 Total Q factor Qts 0.45 Mechanical resistance Rms 2.7 kg/s Moving mass (incl. air load) Mms 17.4 g Suspension compliance Cms 0.48 mm/N Effective cone diameter d 124 mm Effective piston area Sd 120 cm² Equivalent volume Vas 9.8 l Force factor Bl 5.7 Tm Recommended frequency range 40 - 4000 Hz Magnet and Voice Coil Properties Voice coil diameter dc 75 mm Voice coil height hc 10.9 mm Linear excursion, peak to peak 6 mm Max. excursion, peak to peak 17 mm Power Handling Nominal long term IEC (Depending on crossover) 120 W Transient (10 ms) 1000 W Mechanical Properties Net weight 1.2 kg Overall dimension ø 175 x 77 mm Mai usati, comprati per fare un impianto che poi non ho più potuto realizzare, completi di mascherina e guarnizioni, OTTIMO AFFARE!

PREZZO SPEDIZIONE INCLUSA Impact GF 65S mk2 KIT A 2 VIE - 165 mm CARATTERISTICHE TECNICHE Frequency range: 40 ÷ 22.000 Hz RMS Power: 75 W Peak Power: 150 W Speaker Cone: Glass Fiber Tweeter: Silk dome 25mm Protection grills included Il prezzo indicato si riferisce ad una coppia

Causa inutilizzo vendo impianto audio professionale cosi composto: 2 casse passive TOA mod. 380 SE - 3 vie - woofer da 15'' + tromba medi + tweeter (vedi caratteristiche sotto allegate) perfette - originali - mai riparate - 380 watt rms - mede in Canada (USA) + finale di potenza TOA P 150 D - 180 + 180 watt su 8 ohm - perfetto ed originale - una macchina superaffidabile - Se devi fare un impianto fisso in una sala da ballo media - o un impianto di ottima qualita audio fa un grande affare. L'impianto NON è vendibile separatamente - ed è perfettamente funzionante ed originale- Fatto controllare da laboratorio specializzato a Torino Dato il peso degli oggetti NON è possibile la spedizione - Le foto sono reali degli oggetti in vendita - NO perditempo - NON trattabile - NO scambi merce - no cercatori di foto - se sei realmente interessato contattami al cellulare 347 0083722 Annuncio visibil = merce disponibile Caratteristiche tecniche delle casse Enclosure: Vented (bass reflex) type Speakers: Low Frequency, 15" woofer Mid Frequency, CD Horn plus compression driver High Frequency, Horn tweeter Power Handling Capacity Continuous Pink Noise: 120 watts RMS of band-limited pink noise (50 Hz~20 kHz) Continuous Program: 360 watts Impedance: 8 ohms Sensitivity: 102 dB (1W/1m) Input Panel Frequency Response: 50 Hz~20 kHz Crossover Frequencies: 800 Hz, 8 kHz High and Mid Frequencies Level Controls: 0~ –10 dB (with an "OFF" position) Input Terminals: ¼" Phone jacks for a full-range, biamp, triamp and chaining Finish (Enclosure): Polyester in grey color Dimensions: 758(H)X498(W)X410(D)-mm 29.8(H)X19.6(W)X16.1(D) inches Weight: 36 kg (79.2 Ibs)

Causa inutilizzo vendo impianto audio professionale cosi composto: 2 casse passive Toa/Onkyo mod. 380 SE - 3 vie - woofer da 15'' + tromba medi + tweeter (vedi caratteristiche sotto allegate) perfette - originali - mai riparate - 380 watt rms - mede in Canada (USA) + finale di potenza Toa/ Onkyo P 150 D - 180 + 180 watt su 8 ohm - perfetto ed originale - una macchina superaffidabile - Se devi fare un impianto fisso in una sala da ballo media - o un impianto di ottima qualita audio fa un grande affare. L'impianto NON è vendibile separatamente - ed è perfettamente funzionante ed originale- Fatto controllare da laboratorio specializzato a Torino Dato il peso degli oggetti NON è possibile la spedizione - Le foto sono reali degli oggetti in vendita - NO perditempo - NON trattabile - NO scambi merce - no cercatori di foto - se sei realmente interessato contattami al cellulare 347 0083722 Annuncio visibil = merce disponibile Caratteristiche tecniche delle casse Enclosure: Vented (bass reflex) type Speakers: Low Frequency, 15" woofer Mid Frequency, CD Horn plus compression driver High Frequency, Horn tweeter Power Handling Capacity Continuous Pink Noise: 120 watts RMS of band-limited pink noise (50 Hz~20 kHz) Continuous Program: 360 watts Impedance: 8 ohms Sensitivity: 102 dB (1W/1m) Input Panel Frequency Response: 50 Hz~20 kHz Crossover Frequencies: 800 Hz, 8 kHz High and Mid Frequencies Level Controls: 0~ –10 dB (with an "OFF" position) Input Terminals: ¼" Phone jacks for a full-range, biamp, triamp and chaining Finish (Enclosure): Polyester in grey color Dimensions: 758(H)X498(W)X410(D)-mm 29.8(H)X19.6(W)X16.1(D) inches Weight: 36 kg (79.2 Ibs)

Prodipe Natural 6 b'/xc3/xa8' un amplificatore per chitarra acustica da 140 watt dotato di 2 ingressi microfonici con guadagno, EQ a 3 bande, riverbero, volume con l'opzione di alimentazione phantom, 1 ingresso single-ended con guadagno, EQ a 3 bande, riverbero, volume, 1 canale stereo con EQ a 2 bande e volume (stereo RCA), uscita stereo (RCA stereo), uscita mono bilanciata (XLR). Frequency range: 50Hz -20KHz Tweeter: 1b'"' (25mm) - Neodymium Dome Woofer: 6b'/xc2/xbd'b'"' (165mm) - Fibreglass membrane Amplification: HF Power RMS (peak): 40W (60W) LF Power RMS (peak): 100W (180W) Signal to Noise ratio: 92dB SPL level (max): 114dB Input/output impedance: Balanced XLR: 1.5MΩ Unbalanced Jack: 1MΩ RCA: 22Ω EQ boost/cut range: +/- 15dB High frequency: 12KHz Mid frequency: 2.5KHz Low frequency: 80Hz Electronic filtering: Cut-off Frequency: 2.6KHz Subsonic Filter: 45Hz Fuse rating: 100V - 120V: 3.15A 220V - 240V: 1A Audio inputs: 2 XLR/Jack 1 Jack 1 stereo RCA Audio outputs: 1XLR 1 Jack 1 stereo headphone set Dimensioni (H x L x P) en mm: 390 x 320 x 285 Peso: 13kg

Marchio: Ibanez Categoria: Bassi Elettrici a 5 corde Produttore: Ibanez Serie: Premium Design: BTB Corpo: Frassino Top: Palissandro Manico: 9-ply Wenge/Bubinga/Acero Profilo del manico: BTB5 Spessore al 1° tasto: 20 Spessore al 12° tasto: 22 Lacca manico: Opaco Costruzione manico: Neck-through-body Tastiera: Palissandro Radius (raggio di curvatura) della tastiera: 15,75 Tipo di tastiera: Fretted Numero di tasti: 24 Formato tasti: Mediam, acciaio inox Intarsi: Abalone Offset Dots Tipo di capotasto: Plastic + Zero Fret Larghezza dado in mm: 47 Larghezza del capotasto: 76 Scala: Scala extra lunga Scala (pollici): 35 Pickup originali: Aguilar Elettronica: Active, 3-band equalizer Interruttore: Mid Frequency, EQ Bypass Controllo: Vol, Bal, Bass, Mid, Treble Meccaniche: Gotoh Ponte: Ibanez Mono-Rail V Numero di corde: 5 Spaziatura corde (mm): 19 Tracolla: Standard Hardware: Gold Designazione colore: Natural Low Gloss Finitura: Opaco Calibro delle corde:.045 -.130

Amplificatore per acustica marca Crate mod. CA30DG Nuovo in Promozione "Fuori Uno" per singolo prodotto di magazzino 2 anni di garanzia Prodotto ideale per amplificatre strumentazione acustica, chitarre e strumenti ad arco amplificati. chiedi costo spedizione The CA30 Taos compact acoustic amplifier delivers 30 watts RMS and incorporates two inputs, each with its own gain control. Three bands of equalization, with Crate's exclusive Contour control, provide exceptional tone control and minimize feedback. The polypropylene 8" woofer/dome tweeter combination delivers smooth, pristine sound with outstanding projection and fidelity. The CA30 also features 8 of Crate's stunning DSP effects, including short and medium Slapback Delays, Echo, Chorus, Rotary Speaker, Chorus (with Hall Reverb), and two distinct Reverb modes. There's even a front panel Insert jack, so you can add your own effects, and a Line Out jack for chaining additional amplifiers. Crate 8" high fidelity woofer and dome tweeter 30 watts RMS Two channels 3-band EQ and contour (mid frequency) control 8 digital effects with level control Effects loop

Vendo splendido basso praticamente nuovo, nessun segno o graffio, usato pochissimo per studio, manico Atlas-4 in 5pz wengè/bubinga - corpo in mogano con top in frassino e inserto in noce - tastiera in palissandro con inlay in abalone - tasti medium - capotasto Graph Tech BLACK TUSQ - pickup Nordstrand Big Single - EQ Ibanez Custom Electronics a 3 bande con eq. bypass switch e Mid frequency switch - hardware dorato - Monorail bridge. Non spedisco, solo consegna a mano a Taranto e disponibilità a provarlo. Prezzo Euro 700

Basso Elettrico Solid Body 4 corde. Costruzione: Bolt-On - Scala 34" (864mm) Corpo: Swamp Ash. Top: Spalted Maple Top. Manico: Acero Tastiera: Palissandro Inlay Tastiera: Rectangular White Pearl Radius Tastiera: 12" Radius(305mm) Tasti: 22 / Large (2.7mm) Meccaniche: Hipshot lic. Hardware: Chrome Ponte: EB12(4) Pick-Up: Seymour Duncan SJB-3N & SMB-4D Controlli: Duncan designed BEQ-3 EQ, 1 volume, 1 blend, 3 band, mid frequency toggle Corde: D'addario EXL165(105-045) Colore: NAT - Natural Gloss. Condizioni: Nuovo. Note: I DO NOT SHIP TO AFRICA

Marchio: Ibanez Categoria: Altri Modelli di Bassi Elettrici 4 Corde Body: Mogano africano Manico: Acero Roasted/Amaranto Atlas con truss rod KTS Titanium Tastiera: Acero occhiolinato tostato Scala: 864mm Capotasto: 45mm Tasti: 24 Medium, trattamento Premium del bordo dei tasti Pickup: 2x Nordstrand Big Single Equalizzatore: Ibanez Custom Electronics EQ 3-bande con bypass switch (tono passivo su controllo Treble), switch 3-Vie Mid frequency Ponte: MR5S nero Meccaniche: Gotoh Colore: Pearl White Matte Accessori: Gig bag inclusa

Marchio: Ibanez Categoria: Bassi Elettrici a 5 corde Basso elettrico a cinque corde Linea Ibanez Bass Workshop Corpo in mogano Top in pioppo granato Manico a cinque pezzi in noce e jatoba Tastiera in Panga Panga Binding della tastiera in noce Scala: 864 - 901.7 mm (multiscala) Ampiezza del capotasto: 45 mm Ventiquattro tasti medium Pick-Up: Bartolini BH2 (N e B) Elettronica: Ibanez Custom 3-Band EQ con EQ Bypass e Mid Frequency Switch Ponte: MR5S Colore: Deep Twilight

Marchio: Ibanez Categoria: Bassi Elettrici a 5 corde A 5 corde Top: Pioppo Manico: Thru-body BTB5 5pc Acero/Noce con barre di rinforzo in grafite Tastiera: Jatoba Scala: 889mm/35" Capotasto: 47mm Tasti: 24 Medium in acciaio inossidabile Pickup: Bartolini BH2 Controlli: Volume, Balancer, Bass, Middle, Treble Altri selettori: Selettore Mid frequency a 3 posizioni Segnatasti: Abalone Colore: Cerulean Blue Burst Low Gloss

Vendo amplificatore per basso Mark Bass Mini CMD 151P "Custom" Dettagli tecnici sul sito Mark Bass - CUSTOMIZZAZIONE - L'amplificatore e' stato customizzato con queste modifiche: - Tweeter originale (piezo) sostituito con tweeter a ferrofluido Monacor HT-30 - Amplificatori operazionali del preampli (originali: TL072, 0.32 EUR/chip) sostituiti con OPA1642 (SoundPlus Series, 1.91 EUR/chip) - Condensatori elettrolitici del preampli (segnale e alimentazione) sostituiti con componenti a basso ESR / 105 gradi - Jack input, send e return, uscita cassa sostituiti con jack professionali Neutrik - Ventolina raffreddamento sostituita con una a bassa rumorosita' Rispetto all'ampli non customizzato, il suono e' molto piu' definito e dinamico e non presenta piu' quegli alti taglienti enfatizzati dal tweeter piezo originale. Il rumore di fondo (hiss) e' diventato praticamente inesistente. - CONDIZIONI - L'amplificatore e' stato COMPLETAMENTE REVISIONATO (spolverato, pulito, disossidato e testato) a gennaio 2020 Woofer in condizioni perfette (vedi foto) L'unico difetto e' la moquette originale che si e' parzialmente staccata su un lato (vedi foto), dovuta alle centinaia di concerti che ha fatto (visto che suona bene!) Qualsiasi prova a casa mia, se volete portatevi il vostro basso per provarlo per bene Fornisco insieme all'ampli il manuale, il cavo corrente e il tweeter piezo + resistenza originali Non faccio spedizione visto l'ingombro / peso, solo ritiro a mano "visto e piaciuto" INPUTS - INPUT: impedance 500 kOhm, max. voltage 15 Vpp BALANCED INPUT (XLR): impedance 22 kOhm, max. voltage 25 Vpp EFFECT RETURN: impedance 22 kOhm, max. voltage 25 Vpp FREQUENCY RESPONSE: 40 Hz to 18 kHz CONTROLS - GAIN: -80 dB to +23 dB range MASTER VOLUME GROUND LIFT (switch on rear panel) EQUALIZATION - LOW: center frequency: 40 Hz; level: ±16 dB LOW MID: center frequency: 360 Hz, level: ±16 dB HIGH MID: center frequency: 800 Hz, level: ±16 dB HIGH: center frequency: 10 kHz, level: ±16 dB VPF (Variable Pre-shape Filter): center frequency 380 Hz (cut) VLE (Vintage Loudspeaker Emulator): frequency range 250 Hz - 20 kHz (cut) OUTPUT - AMP OUTPUT POWER: 500W RMS su 4 ohms / 300W RMS su 8 ohms LINE OUT: balanced XLR, max. voltage 10 Vpp EFFECT SEND: unbalanced, max. voltage 20 Vpp (pre-EQ) TUNER OUT: unbalanced, max. voltage 25 Vpp SPEAKER OUT: speakon + 1/4" SPEAKER - WOOFER/MID: 1 x 15" TWEETER: piezo - VEDI DESCRIZIONE SOTTOSTANTE BASS REFLEX: rear IMPEDANCE: 8 ohms SPEAKER POWER HANDLING: 400W RMS (AES Standard) CROSSOVER FREQUENCY: 3.5 kHz SENSITIVITY: 100 dB SPL COMBO - WEIGHT: 18.5 Kg HEIGHT: 46.4 cm WIDTH: 46.4 cm DEPTH: 48 cm

DI Plus Read user experiences here. "The ULTRASOUND DI Plus is a very powerful tool for any musician. This is not only a DI but a full featured preamp designed after our famous AG-series amps. Whether at a local open mic night or at a major concert venue, you will be able to dial in the clear natural acoustic sound that our amplifiers are known for, and route it to the stage PA through a balanced XLR output. Sound engineers will appreciate the versatile controls and the optional 48-volt phantom power operation. Therefore, no more wall warts or batteries if your mixer has phantom power. (Originally called ULTRA PDI.) INSTRUMENT INPUT: This input is designed for all passive and active type pickup signals. When a plug is inserted, the 9V battery is switched on. INSTRUMENT OUTPUT: This is a "parallel" jack which can be used to send the "guitar/instrument signal" to an external tuner, guitar amp or other device which can use an instrument level signal. EFX LOOP: This is a real world "EFX LOOP". In an effort to save room, most of our competition uses a TRS jack (tip, ring, sleeve) and Y cable type system. The DI+ is provided with two 1/4" jacks, one for "SEND" and one for "RETURN". Since the EFX LOOP interrupts the signal path it can be used as an insert point for a volume pedal, compressor, or tuner, if the tuner is equipped with a bypass switch. (Try that with one of our competitors units) SEND: The signal on the SEND jack is post-input gain and pre EQ. This means that you can use the SEND signal as an auxiliary unbalanced direct output. This signal is not affected by any of the panel controls with exception of the "INPUT GAIN" control. RETURN: A plug inserted into the RETURN jack will interrupt the signal path. The signal on the tip of the plug inserted into the RETURN jack will be the signal that the DI Plus will process. INPUT GAIN: The "INPUT GAIN" is not a volume control, rather this control sets the level of amplification applied to the input signal to boost it to a useable level. The reason this is adjustable is to accommodate a wide range of pickup devices. BASS: This is an "Active" control. The BASS control adjusts the amount of cut or boost in the low frequency (150HZ) range. TREBLE: This is an "Active" control. The TREBLE control adjusts the amount of cut or boost in the high frequency (5kHZ) range. NOTCH FILTER: ON/OFF - Enables or disables the NOTCH FILTER control. FREQ. HZ - Sets the frequency (100-350HZ) of the 18db cut NOTCH FILTER that is used to control resonant feedback. SHAPE: ON/OFF - This toggle switch enables or disables the SHAPE control. This control is a mid dip control. In the ON position, the mid frequencies will be cut and the high and low frequencies will be boosted. PHASE: IN/OUT - Changes the polarity of the signal. Phase affects the way the guitar top is pressurized by the loudspeakers. When the signals are out of phase with each other, low-end feedback is minimized. If you experience ⤽positive acoustic⤝ feedback on stage, flip the phase switch from its current setting to see if this will kill the feedback. If inverting phase alone does not eliminate feedback, the notch filter can be used. Phase will also affect the way the guitar signal mixes live and when recording. XLR LEVEL: This control adjusts the amount of signal sent to the XLR OUT jack. LINE LEVEL: This control adjusts the amount of signal sent to the LINE OUT jack. 48V: (Phantom Power) This LED lights when there is 48V Phantom Power present on the XLR OUT jack. No battery drain will occur when Phantom Power is present. POWER: This LED indicates the DI PLUS is ready to operate. The POWER LED will illuminate when: A. A plug is inserted into the INPUT jack and there is a fresh battery installed in the DI PLUS. B. A 9VDC adapter (Wall Wart) is plugged into the power jack. (9VDC Regulated Power Supply - 500mA) (2.1MM DC Power Plug, Center +) C. There is 48V phantom power on the XLR cable plugged into the XLR OUT jack. (The 48V LED and the POWER LED will both be illuminated.) XLR OUT: Plug a standard XLR cable from your PA or recording console into this low impedance balanced output. Use the "XLR LEVEL" control to set the output level which matches up best with your PA or recording gear and gives you the least amount of noise. If your board provides 48V phantom power on the XLR cables, the DI Plus will run from this and save the battery. It is suggested that you keep a battery in the unit as a backup when using the phantom power. If the phantom power drops, the DI Plus will automatically switch to battery power. LINE OUT: This is a standard unbalanced line level output signal. Use the "LINE LEVEL" control to adjust the signal level on this jack. This output can be used simultaneously with the XLR OUT jack for some creative signal routing. Plug a standard instrument cable from this output to a stage monitor amp or unbalanced Mic input on a mixer.

DI Plus Read user experiences here. "The ULTRASOUND DI Plus is a very powerful tool for any musician. This is not only a DI but a full featured preamp designed after our famous AG-series amps. Whether at a local open mic night or at a major concert venue, you will be able to dial in the clear natural acoustic sound that our amplifiers are known for, and route it to the stage PA through a balanced XLR output. Sound engineers will appreciate the versatile controls and the optional 48-volt phantom power operation. Therefore, no more wall warts or batteries if your mixer has phantom power. (Originally called ULTRA PDI.) INSTRUMENT INPUT: This input is designed for all passive and active type pickup signals. When a plug is inserted, the 9V battery is switched on. INSTRUMENT OUTPUT: This is a "parallel" jack which can be used to send the "guitar/instrument signal" to an external tuner, guitar amp or other device which can use an instrument level signal. EFX LOOP: This is a real world "EFX LOOP". In an effort to save room, most of our competition uses a TRS jack (tip, ring, sleeve) and Y cable type system. The DI+ is provided with two 1/4" jacks, one for "SEND" and one for "RETURN". Since the EFX LOOP interrupts the signal path it can be used as an insert point for a volume pedal, compressor, or tuner, if the tuner is equipped with a bypass switch. (Try that with one of our competitors units) SEND: The signal on the SEND jack is post-input gain and pre EQ. This means that you can use the SEND signal as an auxiliary unbalanced direct output. This signal is not affected by any of the panel controls with exception of the "INPUT GAIN" control. RETURN: A plug inserted into the RETURN jack will interrupt the signal path. The signal on the tip of the plug inserted into the RETURN jack will be the signal that the DI Plus will process. INPUT GAIN: The "INPUT GAIN" is not a volume control, rather this control sets the level of amplification applied to the input signal to boost it to a useable level. The reason this is adjustable is to accommodate a wide range of pickup devices. BASS: This is an "Active" control. The BASS control adjusts the amount of cut or boost in the low frequency (150HZ) range. TREBLE: This is an "Active" control. The TREBLE control adjusts the amount of cut or boost in the high frequency (5kHZ) range. NOTCH FILTER: ON/OFF - Enables or disables the NOTCH FILTER control. FREQ. HZ - Sets the frequency (100-350HZ) of the 18db cut NOTCH FILTER that is used to control resonant feedback. SHAPE: ON/OFF - This toggle switch enables or disables the SHAPE control. This control is a mid dip control. In the ON position, the mid frequencies will be cut and the high and low frequencies will be boosted. PHASE: IN/OUT - Changes the polarity of the signal. Phase affects the way the guitar top is pressurized by the loudspeakers. When the signals are out of phase with each other, low-end feedback is minimized. If you experience “positive acoustic” feedback on stage, flip the phase switch from its current setting to see if this will kill the feedback. If inverting phase alone does not eliminate feedback, the notch filter can be used. Phase will also affect the way the guitar signal mixes live and when recording. XLR LEVEL: This control adjusts the amount of signal sent to the XLR OUT jack. LINE LEVEL: This control adjusts the amount of signal sent to the LINE OUT jack. 48V: (Phantom Power) This LED lights when there is 48V Phantom Power present on the XLR OUT jack. No battery drain will occur when Phantom Power is present. POWER: This LED indicates the DI PLUS is ready to operate. The POWER LED will illuminate when: A. A plug is inserted into the INPUT jack and there is a fresh battery installed in the DI PLUS. B. A 9VDC adapter (Wall Wart) is plugged into the power jack. (9VDC Regulated Power Supply - 500mA) (2.1MM DC Power Plug, Center +) C. There is 48V phantom power on the XLR cable plugged into the XLR OUT jack. (The 48V LED and the POWER LED will both be illuminated.) XLR OUT: Plug a standard XLR cable from your PA or recording console into this low impedance balanced output. Use the "XLR LEVEL" control to set the output level which matches up best with your PA or recording gear and gives you the least amount of noise. If your board provides 48V phantom power on the XLR cables, the DI Plus will run from this and save the battery. It is suggested that you keep a battery in the unit as a backup when using the phantom power. If the phantom power drops, the DI Plus will automatically switch to battery power. LINE OUT: This is a standard unbalanced line level output signal. Use the "LINE LEVEL" control to adjust the signal level on this jack. This output can be used simultaneously with the XLR OUT jack for some creative signal routing. Plug a standard instrument cable from this output to a stage monitor amp or unbalanced Mic input on a mixer.

Specifications for the Wharfedale Diamond 9.CM Speaker Drivers 2x 6.5" (170mm) Bass 2" (50mm) Mid Soft Dome 1" (25mm) Soft Dome Tweeter Power 150W Nominal Impedance 6 Ohms Magnetically Shielded Yes Sensitivity 90dB Frequency range at -6dB 50Hz - 24kHz HF Limit -10dB 44kHz Crossover Frequency 2kHz Frequency Fb 50Hz Dimensions Width 515mm Height 223mm + 10 on feet Depth 265mm

ROYD ENVOY In Perfette ed eccellenti condizioni, senza segni e perfettamente funzionanti. Attualmente in uso con un setup completo Leak Stereo 20 e pre Leak Point One Stereo. Bellissime esteticamente. Caratteristiche prese dal sito Royd Audio: Dimensions (WxHxD) 203mm x 305mm x 187mm Recommend Amplifier Power 20 to 80 watts Sensitivity 87 dB 1 watt AT 1 metre Power Handling 100 watts Nominal Impedance 8 ohms Drive Units 1 Royd cast chassis 5" bass/mid unit and 1 Royd 18mm dome/cone tweeter Crossover Frequency 4 KHz Bass Resonance Frequency 43 Hz Frequency Range 38 Hz to 20KHz Rosenut veneer, Cherry veneer, Black Ash veneer, Black Ash vinyl 8.2 Kg Spedizione possibile con pacco standar tracciabile a carico e rischio acquirente. Non scambio ma Vendo

CROSSOVER JBL M552 Crossover JBL M552 Stereo Mode: Low/High: 180 Hz to 2 kHz (18 to 200 Hz) (switchable from back panel) Mono Mode: Low/Mid: 180 Hz to 2 kHz (18 to 200 Hz), Mid/High: 800 Hz to 9 kHz Maximum Input Level: +24 dBu, XLR balanced Maximum Output Level: +27 dBu (+25 dBm), XLR balanced Input Impedance: Balanced: 10 kOhms Unbalanced: 20 kOhms Noise: Less than -90 dBu (LF), Less than -88 dBu (HF) THD + Noise: Less than 0.004% (in-band) Frequency Response: 10 Hz (-0.5dB) to 75 kHz (-3 dB) Dimensions (HxWxD): 44mm x 483mm x 144mm (1 3/4in x 19in

Diffusore Acustico made in U.S.A. " JBL L36 Decade " - Dotato di imballo originale, in perfetto stato d'uso & Tecnicamente ineccepibile - Diffusore praticamente nuovo con i driver ancora da rodare - Anno di costruzione 1975 - System Specifications: Tipo: Bass Reflex - Impedenza nominale: 8 ohm - Potenza: 50 WRMS (continuos program) - Frequenza di crossover: 1500 Hz & 6000 Hz - System Sensitivity: 1 Watt imput produces 76dB (sound pressure level at a distance di 15 Feet) - nota: 75/80 dB is a confortable listening level - Angolo di dispersione: 90° oriz/vert. - finitura Mobile: Rovere Naturale - Griglia: estraibile con tessuto elasticizzato originale di colore Bleu - Dimensioni: 34x61x35 cm - Peso: 20,4 Kg. - System Components: Low Frequency Driver: Woofer 125A con Foam sostituito con originale JBL C8R127A nel gennaio 2017 - Impedenza: 8 ohm - Risposta in frequenza: 30Hz a 1200Hz - Gap Gauge:,044" - Diametro: 25 cm - voice coil 5 cm - MID RANGE Driver: LE5-6 - Impedenza: 8 ohm - Gap Gauge:,040" - risposta in frequenza: 75....3000Hz - Diametro: 13 cm - voice coil 3,6 cm - HIGH frequency driver: LE25-2 - Impedenza nominale: 8 ohm - risposta in frequenza: 500/1200 Hz - Gap Gauge:,029" - diametro: 3,6 cm - voice coil 1,6 cm - NOTE: Perfetto stato; imballi, brochure, istruzioni, documentazioni originali in dotazione - *EVENTUALI INFORMAZIONI COMMERCIALI & TECNICHE ESCLUSIVAMENTE PER CONTATTO TELEFONICO *

Coppia diffusori MONITOR AUDIO RX8 biwiring, double bass reflex, in condizioni perfette. Colore rosenut. Completi di basi con piedi a punta regolabili (non visibili in foto poiché preservate a parte), imballi originali e istruzioni. Per amplificatori da 50 a 175W 4 Ohm 90dB. Prezzo intrattabile. Non rispondo ad affaristi e perditempo. Eventuale commissione PayPal 4% a parte. E' previsto il ritiro ma anche la spedizione con costo a parte. MONITOR AUDIO SILVER RX 8 System Format - 3 Way Frequency Response - 32Hz - 35kHz Sensitivity (1W 1m) - 90dB Nominal Impedance - 4 Ohms Maximum SPL - 116.2 Power Handling (RMS) - 175W Recommended Amplifier Requirements - 50 - 175W Bass Alignment - Bass reflex. Twin HiVe®II port System Crossover Frequency - LF/MF: 300Hz | MF/HF: 2.2 kHz Drive Unit Complement: - 2 x 6" RST® Bass drivers - 1 x 6"RST® Bass/Mid driver - 1 x 1" (25mm) C-CAM® gold dome tweeter External Dimensions (H x W x D) - 960 x 275 x 388 mm (37 13/16 x 10 13/16 x 15 1/4 inch) Weight (each) - 21.76 Kg (47.88 lb)

Vendo spettacolare diffusore centrale della casa Monitor Audio Inglese con finitura in vero legno Noce Sono le discendenti con le stesse caratteristiche delle mitiche Studio 20 con accorgimenti più moderni e tecnici, gli audiofili sanno di cosa si sta parlando… Altoparlante versatile a 2 vie che incorpora due driver C-CAM bassi / mid da 6 " e un singolo tweeter C-CAM Gold Dome da 1". Acousticaly abbinato a tutti gli altri altoparlanti RS per l'imaging eccellente e la coerenza del timbro nelle applicazioni surround. Disponibili su richiesta anche i Diffusori Laterali Dx e Sx SILVER RS-6 con le stesse caratteristiche, praticamente nuovi e senza alcun difetto a soli 1150 euro Il diffusore è completo di tutti gli accessori e doppi imballi SPECIFICHE TECNICHE Frequency Response 45 Hz – 30 KHz Sensitivity 91 dB Nominal Impedance 6 Ohms Power Handling (RMS) 120 W Recommended Amplifier Requirements 40 - 120 W Crossover Frequency 2.9 KHz Drive Unit Complement 2 x 6” C-CAM® Bass mid-range. Cabinet Support Rear Ported External Dimensions (H x W x D) 185 x 500 x 200 mm Weight 8.5 Kg Contattatemi solo se seriamente interessati al 335.6487010

Multieffetto rack per chitarra / preamp boss gx700 racchiude in un unico rack tutti gli effetti della serie boss molto caldo e versatile prezzo 200 euro trattabili scheda tecnica boss gx700 guitar effects processor/preamp published in sos june 1996 printer-friendly version • noise gate: with user control of threshold setting. • compressor: with variable attack and release characteristics, plus control over sustain and tone. in common with all the other effects blocks, this also has a level parameter. • wah: this classic effect is familiar to guitarists everywhere, and can be recreated quite convincingly with the gx700, either under lfo or pedal control. the resonance of the wah effect can be varied, as can the frequency range over which the effect sweeps. • distortion: i suspect this section is based around the concepts used in the boss analogue pedals. the choices available include vintage od, turbo od, blues, distortion, turbo distortion, metal and fuzz. in addition to an adjustable drive level, the distortion settings also have a basic 2-band bass/treble equaliser. • preamp: this is where cosm modelling comes into play, because here you can select from several amplifier characteristics, including jc120, clean twin, match drive, big lead, ms1959 (i), ms1959 (ii), ms1959 (i+ii), sldn lead and metal 5150. the available controls include the usual bass, middle, treble and presence, as well as the volume/master volume method of setting the amount of amp distortion, and a 'bright' switch. a gain parameter is also included, which affects the distortion amount. • loop: this isn't an effect at all, but rather a means of switching in an external effect or processor. the loop function connects via the rear panel jacks, and has adjustments for both send and return levels, which is a sensible inclusion. • 3-band eq: despite the fact that the overdrive section and the preamplifier both have tone controls, there's also a 3-band equaliser with a fully parametric mid section. • speaker simulator: this again offers several choices: small, middle, jc-120, built-in 1-4, big stack 1-2, ms stack 1-2 and metal stack. there are also three possible virtual mic settings, for close miking and more distant miking, and separate level controls are provided for the mic level and the direct level. • noise suppressor: this comes at the end of the amplifier chain, but before the effects. however, because the effects can be connected in any order, it can be used elsewhere if you have a reason for doing so. personally, i'd be inclined to use it after the modulation effects (for anything that doesn't involve level modulation, such as panning or vibrato), but before any delay or reverb effects. as far as the user parameters go, these are really down to threshold and release time, though you can also choose to key the gate from either the noise reduction block's own input or from the guitar input jack.

Gli intenditori sanno benissimo di quale prodotto sto offrendo, per cui non aggiungo nulla sulle qualità di questi diffusori. Dico solo che sono in PERFETTE condizioni estetiche e funzionali. In ottimo stato. Comprensive anche di griglie originali (ho dimenticato di fare la foto), anch'esse in ottime condizioni. Questa è la versione con la solida morsettiera metallica invece di quella di plastica. Vedi in foto il numero seriale per verifica dell'effettivo accoppiamento diffusori. Finish: High quality simulated black veneer Grille: Black woven cloth Bass/Mid Unit: ROGERS 160mm Polypropelene cones unit; high flux magnet KAPTON coil former Tweeter: 19mm aluminium dome Crossover: 6 precision elements crossing over at3.5KHz at18dB/octave Dimensions: 356x230x208mm weight: 6Kg each Frequency response: 80Hz-20kHz +- 2dB Nominal impedance: 8 ohms Recommended Amplifier Power: 15-100watts/channel

B&W SCM 8 - HT surround da parete - I monitor Surround Cinema hanno un aspetto e un design unico - Sono dipoli,quindi il suono è proiettato lungo due assi opposti con polarità opposta. Il motivo di questo è la desiderata non localizzazione del suono surround. Gli altoparlanti sono posizionati ad ogni lato dell'ascoltatore con il piano nullo che punta verso l'ascolto, ciò significa che la vastità del suono è riflessa dalle superfici della stanza ed è diffusa in natura. Un ulteriore vantaggio dell' Home THX è nella transizione senza soluzione di continuità tra i campi,anteriori e surround, sonori indipendenti dalla posizione relativa degli altoparlanti - quindi una molteplicità di ascoltatori può sentire il campo sonoro complessivo, e sperimentare la natura dispersiva del suono. La costruzione triangolare di questi diffusori ha diversi vantaggi, funzionali come pure estetici, in primis la forma triangolare riduce i livelli di onde permanenti all'interno del cabinet in modo da irradiare il suono senza colorazione - Description: Wall mounting second-order closed-box system with dipolar radiation - Characteristics: Drive units: 2 x 25mm dome high-frequency unit with metal diaphragms, high power voice coils and magnetic fluid cooling - 2 x 160mm Kevlar bass/mid - Frequency response: 105Hz - 25kHz ± 6dB on reference - Frequenza xover: 3KHz - Sensitivity: 87dB spl (2.83V 1m) - Nominal impedance: 4 ohms - Power handling: 50W - 200W into 8 ohms on unclipped programme - Dimensioni: Height: 362mm; Width: 352mm; Depth: 251mm - Peso: 14 Kg. cad. Finishes: Black Ash - Grille: Black Cloth - Asportabili n. 4 x diffusore - Note: Magneti schermati, Conforme e certificato THX - Struttura interna Matrix - Prezzo di listino nel 1994 era di £: 3.400.000 - Perfetto funzionamento - *informazioni esclusivamente per contatto telefonico *

Vendo in perfette condizioni estetiche e funzionali con la relativa scatola. Boss HF-2 HiBand Flanger The HF-2 is combining the original signal with a delayed signal that is shifted one octave up to create a flanging effect a bit different but still similar to the BF-2. The effect is brighter and cleaner than the BF-2. The HF-2 may not be as powerful as the BF-2, but for hi frequency flanging it produces a very good result. Production of the HF-2 moved from Japan to Taiwan mid 1989. Specifications Controls: Manual, Depth, Rate, Res Connectors: Input, Output, AC Adaptor Current Draw: 15 mA (DC 9V) Weight: 400 g (14 oz.) Input Impedance: 470 kOhm Residual Noise Level: -95dBu (IHF-A) Recommended Load Impedance: 10kOhm or greater Delay Time: 0.5 ms ~ 6.5 ms LFO Speed: 100 ms ~ 16 s Recommended AC Adaptor: ACA Series

Type: Amateur VHF/UHF transceiver Frequency range: 144-146 / 430-440 MHz (10 m, 6 m or 23 cm options) Mode: FM RF Power output: Hi: 50/35 W Mid: 10/10 W Lo: 5/5 W Sensitivity: N/A Selectivity: N/A Image rejection: N/A Voltage: 13.8 VDC Current drain: RX: Max 1.2 A TX: Max 11.5 A Impedance: 50 ohms Dimensions (W*H*D): 150*50*175 mm Weight: 1.5 Kg Other: 101 memories. Triple RX New price 1995 in Sweden: 11233:- SEK Allegati: TM-742 - TM-792 - Manuale utente italiano 31593 kB TM742_TM942_service_manual.pdf 10490 Kb USATO SOLO DUE VOLTE, E POI CONSERVATO NELLA PROPRIA SCATOLA IL PREZZO SI CONCENTRA SUI 600 EURO TELEFONARE SE REALMENTE INTERESSATI. 338/8520912

Type: Amateur VHF/UHF transceiver Frequency range: 144-146 / 430-440 MHz (10 m, 6 m or 23 cm options) Mode: FM RF Power output: Hi: 50/35 W Mid: 10/10 W Lo: 5/5 W Sensitivity: N/A Selectivity: N/A Image rejection: N/A Voltage: 13.8 VDC Current drain: RX: Max 1.2 A TX: Max 11.5 A Impedance: 50 ohms Dimensions (W*H*D): 150*50*175 mm Weight: 1.5 Kg Other: 101 memories. Triple RX New price 1995 in Sweden: 11233:- SEK Allegati: TM-742 - TM-792 - Manuale utente italiano 31593 kB TM742_TM942_service_manual.pdf 10490 Kb USATO SOLO DUE VOLTE, E POI CONSERVATO NELLA PROPRIA SCATOLA IL PREZZO SI CONCENTRA SUI 600 EURO TELEFONARE SE REALMENTE INTERESSATI. 338/8520912 Vige la clausola Come visto e piaciuto nello stato in cui si trova

Type: Amateur VHF/UHF transceiver Frequency range: 144-146 / 430-440 MHz (10 m, 6 m or 23 cm options) Mode: FM RF Power output: Hi: 50/35 W Mid: 10/10 W Lo: 5/5 W Sensitivity: N/A Selectivity: N/A Image rejection: N/A Voltage: 13.8 VDC Current drain: RX: Max 1.2 A TX: Max 11.5 A Impedance: 50 ohms Dimensions (W*H*D): 150*50*175 mm Weight: 1.5 Kg Other: 101 memories. Triple RX New price 1995 in Sweden: 11233:- SEK USATO SOLO DUE VOLTE, E POI CONSERVATO NELLA PROPRIA SCATOLA IL PREZZO SI CONCENTRA SUI 300 EURO TELEFONARE SE REALMENTE INTERESSATI. 338/8520912 Vige la clausola Come visto e piaciuto nello stato in cui si trova

Vendo spettacolari diffusori della casa Monitor Audio Inglesi con finitura in vero legno Rosewood Sono le successive discendenti delle mitiche Studio 20 con accorgimenti più moderni e tecnici, gli audiofili sanno di cosa si sta parlandoâ€| La sua configurazione a due e mezzo, a tre driver, è costruita attorno a un esclusivo design a due cavità del cabinet, in cui i bassi 6 1/2 "RST II e i driver mid-basso funzionano in enclosure separate, sintonizzati su frequenze diverse e impedenze. Ciò fornisce una migliore gestione della potenza e offre bassi più veloci, profondi e più dinamici e una maggiore trasparenza attraverso la gamma media cruciale. Oltre a ciò, il tweeter C-CAM Gold Dome garantisce un suono fluido e dettagliato fino a 43 KHz, sfruttando tutto il potenziale dei più recenti formati digitali a larga banda. I diffusori sono completi di tutti gli accessori e doppi imballi SPECIFICHE TECNICHE Risposta in frequenza 32 Hz - 45 KHz Sensibilità 89 dB Impedenza nominale 6 ohm Power Handling (RMS) 150 W Requisiti dell'amplificatore raccomandati 40 - 150 W Bass Alignment Reflex a doppia camera con sintonizzazione differenziale (tecnologia HiVe II) Frequenza di crossover 2,7 KHz Bass Crossover Frequency 250 Hz Complemento unità di azionamento 1 x 6 1/2 " bass driver RST II 1 x 6 1/2 " RST II bass / mid driver 1 x 1 "(25 mm) tweeter C-CAM Gold Dome Dimensioni esterne (escluso zoccolo (H x L x P)) 924 x 206 x 280 mm Dimensioni esterne (compreso lo zoccolo (H x L x P)) 934 x 322 x 363 mm Peso 20,6 kg Contattatemi solo se seriamente interessati al 335.6487010